note: this is an excerpt from my book, Soldering Beyond the Basics. There is more about setting up your studio in the book.
My students ask me all the time about setting up a studio. Most of us learn jewelry in a classroom, where the metalsmithing department is full of benches, tools, polishing and casting equipment.Translating that big space into your own studio is overwhelming, but the truth is that a jewelry studio can be as small as one table or a bench.
Now, the words “home” and “studio” may not seem like a reasonable combination, especially when considering using jewelry tools, torches, flex shafts and such. It naturally brings up common questions, like is it safe? where should I put my studio? can I solder at home? The answers are yes, almost anywhere, and absolutely. I’ve worked in goldsmith shops and lots of studios. They were parts of retail shops, home studios or office spaces. The floors ranged from wood to carpeting - not your first choices in fire safety. Bench tops were made of wood, walls were normal dry wall. And yet, we never had a fire. Why? Because we practiced commonsense safety rules.
Later, when I became an independent jeweler, I took what I learned about work place safety to my home, where my studios ranged from spare bedrooms, half of a room, a shed in the yard, even a little 6x6’ space outside of my bathroom! That tiny space contained my bench, a casting machine, polishing motor, kiln and everything else I used to solder, fabricate and cast jewelry. Your studio can start with just a bench or sturdy table, with just a little organization. And once it’s set up, you can make jewelry anytime you want. As long as you don’ wake up the neighbors!
Basic Safety Rule #1: The flame stays where it belongs.
The first safety rule to learn is to keep the flame where it belongs - in the soldering area! This includes igniting the torch, which for some reason, most beginners think should take place while pointing the torch in the air, at the table, into the bench or even at each other! The only surfaces that can safely take the intense heat of any torch are your solder board, charcoal, fire bricks, etc. Everything else burns: you, your table, the carpet, etc.
Setting up for Safety
Obviously soldering is the number one concern for safety. Sawing, filing, even polishing with the clean bits I recommend are benign when compared to flames and red hot metal. With a few simple precautions, you can solder safely at home.
Protect your Table
Heat will eventually pass through a solder board and burn an unprotected table. Work on a flame proof table or protect the table you have with something fire-proof. Not everyone has a steel table. Most benches and tables are made of wood.Put something under your board, like a 1x1’ ceramic floor tile. Keep the solder area clear of anything flammable, like paper or plastic.
The next level of protection would be to cover the table top with concrete tile backer board, available at hard ware stores. Score it with a utility knife and then snap it to size. Want more protection? Set up a torch station with some landscaping bricks. [ B ] This is a good choice for tank torches, especially if they have large tips with big hot flames. A station like this can handle soldering, annealing, even casting ingots. Put a sheet of steel down as a base to catch small parts. The brick wall around the sides help to keep the flame where it belongs - inside the work area.
Protect your Room
Let’s face it - gravity works even in the studio, so eventually something hot will fall on the floor. If you care about your floor, protect it with a remnant carpet or mat. Just confirm that anything hot that falls on your safety mat is quenched and doesn’t smolder.If you set up to solder less than 3 feet from a wall, protect it with a sheet of concrete tile backer board.
Where to set up your studio
The best place to set up your studio is in an open space that has some natural ventilation, like near a window. The worst place to set up would be in a confined space, like a walk-in closet. Even though this book emphasizes safer tools and chemicals, there are still some fumes that could affect your health if you solder full time for years. Solders contain zinc, and when they flow a little is released as gas. Some flux contains fluorides, which also create fumes. Non-fluoride fluxes are a healthier alternative. Keep your face back from the solder area. Hovering your face over the board is a one way ticket up your nose for heat and fumes.
A simple way to increase ventilation is to work near a fan. The fan should blow away from your solder area, to draw the air. A low budget ventilation system can be made with ducting from the hardware store and a window fan. The ducting sends any fumes out the window. An kitchen exhaust hood works, too, but has to be installed. Lightweight respirators and dust masks rated for minor fumes from soldering are available from jewelry suppliers.
Set up your studio near a water source, to refill quench bowls, pickle pots and for cleaning. The best choice would be a utility sink, something not shared with food or dishes. In my studio that was in a small building in our yard, I filled a container with a spout, like a drink cooler, and used a big bowl to make a quick sink. The pickle pot can be on the bench with a tray to catch spills, or near your sink.
Good lighting can make a big difference in your studio. Natural light is best, but it’s easy to add a good lamp to your work area. Daylight matching bulbs are good for reading detail and color. One draw back to too much light is that it’s difficult to see the first stages of heat on metal, as it glows a light pink, especially on silver. Dim the light or use a shade. A soldering station with bricks can have another steel sheet across the top for a hood, providing shadow while you solder or anneal.
Jewelry Benches vs. Kitchen Tables
One or two sturdy tables can make a perfectly usable work area for jewelry. One of my benches was made with a table top on top of two drawer units. Use solid wood tops to withstand hammering. Lighter tables can be braced against a wall. Bench pins, for sawing and filing, can be clamped to the table or screwed in place. The drawers were used to store tools. Labels made it easy to put them away - if a tool has a home, it has a place to go.
Normal tables are low for jewelry work. Sawing, filing, even soldering is best when the table is raised to counter height, about the level of your clavicles. If the work is too low, then your neck and back will hunch, causing injury and pain over time. When seated, your eyes are close to the work, which promotes better posture. [ D ] Use an adjustable chair to raise and lower yourself for the job at hand. Down to be closer to the pin to see better while filing, sawing, or setting. Raised for soldering. The soldering area can be raised with a stack of fire bricks or charcoal blocks, and the pin can be put in a bench vise, adding another few inches of height, if the chair can’t be lowered enough.
Filing and sawing make a lot of dust, and sterling dust is worth money. If you file over a tray, you may be stunned by the amount of dust that piles up! Filings and small bits of metal can be recycled for credit or cash at a metal refinery. A table doesn’t have a tray, like a bench for catching metal, but with a little imagination, one can be added. One solution is to wear your tray! Wear an apron that is hooked to the underside of the table. The apron makes a bag underneath the pin, catching filings. Snapping the bottom of it gathers all the bits in the middle for collection. Just don’t forget to take it off before you get up!
A jewelers bench is ergonomic helps you organize your tools. It’s like customized tool box with a place to work! [ E ] Benches can cost under 200 dollars or over 2000, and are simple enough to make your own, if you or someone you know is handy. The height can be customized for you by sawing the legs, and most come equipped with a sweeps tray for filings, drawers for tools, and a bench pin. The top of the bench is a little high for some tasks, like hammering, but you can stand, put the anvil in your sweeps drawer, or use a lower table.
Make your bench work for you by making places to store your tools within easy reach. Bench aprons can be attached that telescope out with hanging storage for files, pliers, and hammers. [ F ] The shelf inside the bench can hold lengths of inexpensive plastic pipe, to organize your files. [ G ] And there are lots of bench accessories that save space, transforming themselves from a bench pin to a solder board, for example. [ H ] An organized bench packs most of what you need into a small space.
Check out pictures of real home studios submitted by our students on our Facebook page.
A great resource for lots of ideas about how to organize your bench and studio is Charles Lewton-Brain's book, The Jewelers Bench Book. One of my favorites! I highly recommend it.